Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Panel Replacement Cost in Edison?
Panel replacement in Edison typically costs $250 – $500 per section, depending on the panel’s size, material and whether the section is a stock profile or a custom order. A single dented bottom panel on a standard steel door usually lands near the low end, while insulated or brand-matched sections from Clopay, Amarr or Wayne Dalton push toward the top of that range. The written estimate we provide after seeing the door sets the final price.
Here’s the short version for anyone in a hurry: you’re looking at roughly $250 – $500 for a straightforward panel swap in Edison, and the number moves based on material, insulation and how easy the panel is to source. Call (855) 506-5081 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Typical panel replacement in Edison runs $250 – $500 for a single section.
- Brand-matched panels from Clopay, Amarr, Wayne Dalton and Raynor cost more than generic profiles.
- Matching paint and profile to an existing door is the biggest swing factor in price.
- A section that’s only dented or scratched is often the cheaper route than a full door replacement, which runs $700 – $2200.
- We work on your exact system, so a LiftMaster opener and a Clopay door stay on the same service call rather than getting handed to a second contractor.
Panel Replacement Cost Breakdown (2026)
The table below shows typical estimated ranges for the most common panel and related repair jobs we see in Edison. These are not quotes. Every door gets a written estimate after we look at it, and that estimate sets the price you actually pay.
| Job | Typical Estimated Range |
|---|---|
| Single panel replacement | $250 – $500 |
| Panel replacement (matched pair of adjacent sections) | $500 – $1,000 |
| Spring repair (one spring) | $180 – $340 |
| Cable repair | $130 – $250 |
| Opener repair | $120 – $320 |
| Opener installation | $250 – $550 |
| Track realignment | $120 – $240 |
| Roller replacement | $110 – $220 |
| General garage door repair | $150 – $600 |
| Full new door installation | $700 – $2200 |
What pushes a panel job toward the top of the $250 – $500 range? Insulated panels cost more than non-insulated ones because the core adds material and weight. A panel that has to be ordered to match a discontinued color, a long-panel profile, or a specific Clopay or Amarr model costs more than a standard profile we can source quickly. On the low end, a plain steel bottom section on a common door is the simplest and most affordable repair. The panel itself is only part of the number, too. Removing the old section, sliding the new one into the existing tracks, and re-hanging it so the door travels straight all take time, and that labor is part of the estimate.
If a door has two or three damaged sections next to each other, we usually recommend replacing them as a set rather than piecing them one at a time. It’s cheaper per panel and the finished door looks even. That’s the $500 – $1,000 line above, and it’s worth an honest conversation before you commit to a single-panel fix that leaves mismatched sections behind.
What Affects Panel Replacement Pricing in Edison
Two doors on the same street in Edison can price very differently. Here’s what actually moves the number.
- Panel material and insulation. A non-insulated steel panel sits at the bottom of the range. Insulated steel, aluminum and composite panels cost more, and some of the older homes around the Clara Barton and Stelton sections have doors built to a heavier spec that only a matched panel will fit cleanly.
- Brand-matching. If your door is a Clopay, Amarr, Wayne Dalton or Raynor, we source the correct replacement section for that model rather than a generic panel that nearly fits. Getting the exact profile and color right is what keeps the repaired door looking original, and it’s the part a generalist usually guesses at.
- How many sections are damaged. One panel is the low end. A cluster of two or three takes the price toward $500 – $1,000 because the sections are replaced together and the labor stacks.
- Color and finish matching. A standard color still in production is straightforward. A discontinued color or a custom finish means a longer search or a color-close match, both of which raise the estimate.
- Related damage. A dented panel often comes with a bent track, worn rollers or a tired spring. If the door isn’t traveling straight, we’ll quote the panel plus whatever else needs attention, so you’re not calling a second company later. Our panel replacement service covers the panel and the surrounding hardware in one visit.
- Door design and age. Larger and heavier doors can need extra hands to lift a section safely into place, and older doors sometimes need small adjustments to old hardware so the new panel seats properly.
One thing worth saying plainly: this is not a job to hand to a general handyman. A garage door is under constant spring tension even when it’s closed, and swapping a panel means working near the springs and the lift mechanism. It’s not a spot for trial and error.
How to Save on Panel Replacement
Panel replacement is one of the few garage door jobs where careful timing and a little research actually save money.
- Fix it before it spreads. A dented panel that lets water and dirt in can rust the interior, which can turn one replacement into two. Handling it early keeps the job in the $250 – $500 range.
- Replace adjacent sections together. Doing two panels at once costs less than two separate visits, and the finished door looks better than a mismatched patch.
- Know your door’s brand. Tell us up front if you have a Clopay, Amarr, Wayne Dalton or Raynor door, and the opener’s brand too. Knowing the exact system lets us quote accurately the first time rather than arriving to find an unexpected model.
- Bundle a tune-up. If the same visit turns up worn rollers or a loose track, we can often fold that work into the panel estimate and save you a second appointment.
- Get a free estimate. The most reliable way to know your number is to have someone look at the door. Call (855) 506-5081 and we’ll give you an upfront estimate, with no fee to have us out.
We work on all of the industry’s most widely installed door and opener brands, including LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman and Raynor. That matters here in Edison, where a lot of homes have name-brand systems that a generalist would guess at. Our technicians know the mechanics of each one, and they’ve got up to 11 years of experience behind that knowledge. We work on your exact system, not a lookalike.
Is it cheaper to repair a panel or replace the whole door?
Repairing a single panel at $250 – $500 is almost always cheaper than a full new door, which runs $700 – $2200. Replace the whole door only when the damage is widespread, the sections are structurally compromised, or you want a different style or insulation level. If one or two panels took the hit and the rest of the door is sound, a panel replacement is the sensible move. Call (855) 506-5081 and we’ll tell you straight which one makes sense for your door.
FAQs – Panel Replacement Cost
How much does panel replacement cost in Edison?
Panel replacement in Edison typically costs $250 – $500 for a single section. The range covers the panel itself plus the labor to remove the old one, slide in the new one, and re-align it in the tracks. Insulated panels and brand-matched sections toward the top; standard steel at the bottom. Call (855) 506-5081 for an exact quote, free of charge.
Can a dented garage door panel be replaced instead of the whole door?
Yes. A single dented, scratched or bent panel can be replaced on its own, usually for $250 – $500, as long as the rest of the door is structurally sound and the panel profile can be matched. You don’t need a new door for one damaged section. Call (855) 506-5081 and we’ll confirm what your door needs.
Why does panel replacement cost more for some doors than others?
Material and brand-matching drive most of the difference. A stock steel panel is at the bottom of the $250 – $500 range, while an insulated panel or a panel cut to match a Clopay, Amarr, Wayne Dalton or Raynor model is at the top. Color matching a discontinued finish and folding in related hardware repairs both add to the total. The written estimate is what sets your price. Call (855) 506-5081 to get one.
Can you come today for a panel replacement estimate?
Same-day service is often possible. We answer 24/7, and we dispatch technicians Sunday through Friday, 7am to 7pm. A call outside those hours is booked into the next opening. Call (855) 506-5081 and we’ll find you the earliest slot.
Does a damaged panel mean I need a new garage door opener too?
Not usually. If the opener is a LiftMaster, Chamberlain, Genie or Craftsman system and it’s still running the door, the panel is the only issue. We’ll check the opener during the visit, and opener repair runs $120 – $320 if something does need attention. Call (855) 506-5081 to book a visit and we’ll look at the whole door.
What’s the difference between panel replacement and a full garage door repair in Edison?
Panel replacement is a specific fix for a damaged section and lands at $250 – $500. A general garage door repair at $150 – $600 covers everything from springs to tracks to cables. If your door has more than a cosmetic dent, the broader repair is usually the right call because it addresses the cause, not just the panel. Our Edison Garage Door Repair Pros team can diagnose the difference on-site. Call (855) 506-5081 to book an estimate.
Why Choose Us for Panel Replacement in Edison
We’re a garage door specialty company. Every job we take stays within the garage door trade, from a broken spring to a full new installation. That focus is why we can quote a panel replacement correctly the first time and why the door gets diagnosed correctly on the first visit. We handle the door and the opener together, including LiftMaster myQ, Chamberlain, Genie Aladdin and older legacy systems, so a panel job and an opener check don’t become two different contractors.
Springs are under extreme tension, and a panel swap puts a technician close to that tension and the lift hardware. If something feels off after a repair, or a door jams or slams, don’t force it. Call us and we’ll take a look. Emergency service is a normal part of what we do, and a door that won’t close or won’t open is exactly the kind of call we’re set up to handle. We answer 24/7, and we dispatch Sunday through Friday, 7am to 7pm.
Our technicians have up to 11 years of experience with the top eight brands in North America. That means when your door is a Clopay, Amarr, Wayne Dalton or Raynor, or your opener is a LiftMaster, Chamberlain, Genie or Craftsman, we arrive already knowing the mechanism. No guessing at which panel profile fits or which opener logic applies. We work on your exact system.
Book a Free Panel Replacement Estimate in Edison
If you’ve got a dented, cracked or bent panel and you want a straight number before anything gets scheduled, call (855) 506-5081. We’ll come out, look at the door, and give you a free written estimate that sets the final price. Same-day service is often available, and a call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Whether you need a single panel swapped or a matched pair, we’ll quote it honestly and do the work in one visit.
Pricing reflects the Edison market as of 2026. Edison Garage Door Repair Pros offers free estimates – call (855) 506-5081.
Written by the team at Edison Garage Door Repair Pros.
What Our Customers Say
"Replaced the bottom panel after I backed into it. Color match is close enough that you have to know to look for it."
- Sanjay Rao"Track was bent and two of the rollers were shot. He straightened what he could, swapped the rollers for nylon ones, lubricated everything, and had it done in about an hour."
- Sanjay Patel"Keypad stopped working, which I assumed meant a whole new system. It was the batteries and a reprogram. He charged me the minimum service call and told me how to do it myself next time."
- Karen Nguyen